PASSPORT AND INSTRUCTIONS FOR USE Ksital GSM-4
INSTALLATION
The installation of the Xital GSM-4 system is carried out in accordance with the requirements for the installation of low-voltage equipment and fire and security alarms. An unshielded 4-wire cable with a wire cross section of at least 0.15 mm2 and a total length of not more than 40 meters must be used to connect remote temperature sensors and an electronic key reader to the controller. To connect various sensors to the controller, an unshielded 2- or 4-core cable with a wire cross section of at least 0.22 mm2.
SELECTION OF THE INSTALLATION PLACE OF THE CONTROLLER The location of the controller is selected from the following considerations: • the ingress of moisture on the controller and power adapter is excluded • there must be a 220V electrical outlet nearby • at the location of the controller or remote antenna there must be a reliable reception of the signal from the cellular station The signal level can be estimated using a cell phone that has a SIM card from the same mobile operator as the controller. Confident reception is 4-5 bars (out of 5) on the cell phone indicator. The controller is mounted on the wall using self-tapping screws for the mounting ears of the case.
CONNECTING REMOTE THERMAL SENSORS Before connecting remote temperature sensors, they must first be registered (see the section "Registration of additional temperature sensors"). To connect, it is necessary to connect the remote temperature sensors to each other and to the “Touch Memory electronic key reader” input of the controller using the cables provided in the kit or made in accordance with the table (see the section “Mounting the reader and connecting to the controller”). Both inputs of the temperature sensor are equivalent. The sequence of location and connection of temperature sensors does not matter.
CONNECTING A BACKUP BATTERY The battery is connected to a specially designed for this socket of the controller using the connector included in the delivery set (“+” is connected to the external contact, and “–” to the internal one). The controller provides effective charging of the battery with a capacity of not more than 7.2A / h. A new battery is sold, as a rule, charged and does not require any preparation before connection.
CHANGING THE COMPOSITION OF THE SYSTEM The user can independently change the composition of the system by connecting additional remote temperature sensors, additional Touch Memory electronic keys.
REGISTRATION OF ADDITIONAL TEMPERATURE SENSORSAdditionally registered temperature sensors will receive numbers: No. 2, No. 3, No. 4, No. 5, No. 6. In order to register an additional temperature sensor in the system, do the following: • turn off the controller's power • disconnect all devices except the key reader from the “Touch Memory electronic key reader” connector and connect only the newly registered temperature sensor to it • turn on the controller's power After a while, the number 00 SMS will send a message indicating the number of the newly registered temperature sensor. The registered temperature sensor is automatically assigned an increasing serial number. After successful registration, do not forget to mark the sensor with its number.
SYSTEM MANAGEMENT The controller analyzes incoming SMS and incoming calls. To avoid overflowing the SIM card memory, all incoming SMS messages are deleted after decryption. If the received SMS contains a command of the required format and the correct system password, then the command is executed. For the correct formation of SMS commands sent from some phones, for example, from NOKIA, it is necessary that the message language - English is selected in the settings of this phone. It is assumed that SMS with control commands are prepared in advance and the user simply sends the required SMS if necessary.For ease of use, many commands allow you to include arbitrary text. This allows you to make the command more clear and memorable.
Yes, that's what I need download instructions for the warning and control system Xital GSM-4
Advantages
- In addition to monitoring the functioning of heating equipment units, Ksital GSM 4T alarms allow you to notify using SMS messages and voice dialing about the operation of sensors / sensors connected to the inputs of the Ksital 4T electronic unit. These can be motion sensors, sensors for opening windows / doors, glass breaking, sensors for gas, water, smoke, etc.
- The text in the SMS message can be individual for each of the available inputs. It adapts to the type of sensor that is connected to the respective input. If necessary, text messages can be duplicated by a voice call with an "Alarm" notification. Sending SMS messages is carried out to telephone numbers that are recorded in the memory of the SIM card during the time when the Xital GSM 4T is configured.
- Special service SMS messages are used to control the operation of equipment controlled by GSM alarms. They act on the controller, which turns on or off the relay system controlled by external mechanisms. For correct use by Xital GSM 4T service commands, the instruction manual describes in detail their correct spelling and functional purpose.
Specifications
| Parameters | Values |
| Manufacturer country | Russia |
| Guarantee | 1 year |
| Supply voltage | 12 VDC |
| Backup power | external battery |
| Working temperature | — 25 °C…+ 50 °C |
| Number of alert numbers | 10 |
| Number of hardwired zones | 4 |
| Number of temperature sensors | 1 built-in, up to 5 remote (2 included) |
| Measured temperature | — 55 °C…+ 125 °C |
| Number of outputs | 3 (type "relay" 5A/220VAC) |
| Microphone | Remote (not included) |
| dimensions | 150 × 111 × 40 |
| Weight | 850 g |
How does the alarm work?
Xital GSM 4T systems include one built-in and 5 remote temperature sensors that continuously measure the temperature in the room. The electronic unit, which is owned by the GSM alarm system Ksital, collects information from all sensors / sensors and analyzes it in accordance with a special algorithm.
If the temperature in one of the zones controlled by temperature sensors goes beyond the set limits, a danger alert will be sent to selected phone numbers. Devices of this series allow simultaneous control of 4 zones. To increase the number of controlled zones, the Ksital 12T series alarm system can be used.
To improve the fault tolerance and reliability of systems that control heating equipment and the situation at the facility, it is practiced to use 2 Xital systems, which are used as “partner devices”. For example, together with Xital 4T, Xital GSM 12T can be used - the instruction describes in detail the possibility of paired use of two alarms.
What actuators are connected?
GSM alarm system Xital GSM 4T allows you to connect up to 3 actuators. These can be sound sirens, light emitters, valves and locking mechanisms, control devices for air conditioning systems, forced ventilation, smoke removal, and so on.
The control of the connected devices is carried out automatically using a microcontroller, which is equipped with the Xital GSM 4T alarm or through service SMS commands sent from a mobile phone.
Who can carry out the installation?
Installation of Xital GSM 4T is carried out by specially trained specialists of companies that specialize in the installation of fire and security systems.
In addition, users who are “well acquainted” with electronics can independently install and configure the Xital GSM 4 alarm - the instruction will help you perform these procedures quickly and accurately.
https://youtube.com/watch?v=RZVgv73e5-M
Temperature monitoring functions
GSM alarm system Xital GSM 12T has one built-in temperature sensor and can support up to 5 external ones. With their help, continuous collection of data on the temperature in the controlled area is carried out. If the temperature goes beyond the set limit values, the alarm will send SMS messages to the recorded mobile phone numbers.
In addition, the alarm also supports the possibility of automatically adjusting the optimal temperature regime by controlling the operation of the heating system. For this purpose, built-in relays are used, which, if necessary, turn off or turn on the heating system.
Complete set of alarm
The GSM-12T alarm includes the following elements:
- control controller with integrated GSM-adapter;
- receiving and transmitting GSM-standard antenna;
- autonomous 12-volt power supply;
- AC power adapter;
- Touch Memory master key and a reader of this type of keys (keys are supplied separately).
- auxiliary devices (external thermal sensors, sound detectors, audio microphones, expansion modules are supplied separately).
How to connect Xital GSM 12T?
Installation of Xital alarms must be carried out in accordance with the rules that apply to fire and security alarms. For Ksital GSM 12T connection of remote temperature sensors, expansion modules and Touch-key reader, unshielded 4-core cables are used, the total length of which should not exceed 100 m.
The location of the alarm controller should be selected from the following principles:
- there is no chance of moisture getting on the controller itself and its network adapter;
- it must be possible to connect to a 220 V network;
- in the place where the GSM antenna is installed, there must be a strong and stable cellular signal.
The electronic key reader is traditionally installed indoors just behind the front door.
When using remote temperature sensors and expansion modules in Xital GSM 12T systems, their connection must occur through the preliminary registration of these devices. To do this, connect the temperature sensors, the key reader and the expansion module to each other, and then to the controller input through which the Touch-Memory electronic keys are read.
An autonomous battery is connected to a special connector through which the battery is also recharged when the controller is powered by an external 220 V network.
GSM signaling scheme Xital 12T
The Xital alarm system supports the control of 12 active zones of the facility. For each of the zones, the required number of sensors can be used, which are connected into one security loop connected to the alarm controller. In addition to wired sensors, the Xital GSM 12T system also supports wireless devices.
Main technical data
| Parameters | Values |
| Number of built-in relays: | 3 |
| The value of the operating power when powered by 220 V: | 10 W |
| The value of the maximum switching power: | 200 W |
| Number of control zones supported: | 12 |
| The maximum number of phone numbers for sending SMS and dialing: | 10 |
| Operating temperature range: | -35ºС…+50ºС |
| The value of the overall dimensions of the controller: | 150x110x40 mm |
| Weight of the device with packaging: | 1.25 kg |
