Moving a kitchen sink

Best Answers

Truculentus:

What redevelopment of the apartment can be made without permission. They are called "minor" :

• Remove and install built-in wardrobe. • Move an electric or gas stove. , sink. • Move the battery closer to the riser. • Install an air conditioner or a satellite dish. • Glazed and insulated loggia or balcony. • Put a shower cabin instead of a bathtub. • Seal openings in the load-bearing wall. • Demolish a non-bearing interior wall (if the kitchen does not have a gas stove). • Make an opening in the interior partition. • Combine a bathroom with a toilet. • Install a new partition (not thicker than 10 cm) . • Replace sewer pipes and electrical wiring. • Lay parquet and level floors.

What is forbidden to do with your apartment:

1. Increase the area of ​​bathrooms and bathrooms at the expense of residential premises, transfer them to other premises. 2. Any intrusion into the supporting structures (even if we are talking about a niche for a microwave oven). 3. Dismantling of balcony blocks

For example, it is forbidden to combine loggias and balconies with other rooms by dismantling external walls (whether they are load-bearing or not). 4

Transfer central heating batteries to loggias and balconies. 5. Combine apartments vertically with complete or even partial dismantling of interfloor ceilings. 7. Dismantle ventilation ducts and boxes. 8. Dig cellars, create extensions to apartments located on the first floors of high-rise buildings. 9. Install air conditioners and satellite dishes on the facades of buildings facing the street.

kisunya):

rearrange it

Vasily Alibobaevich:

No. Transfer.

yes no clicks:

no, but if you can carry the slippers, then yes

Tatyana:

Of course, you must first go to the BTI, well, there is somewhere else to go.

Flaws

As it turned out, there are not so many advantages at the sink under the window. The main factor is aesthetics. If the view really deserves it, then you can move the sink. The main thing is to familiarize yourself with the shortcomings of such a solution in advance.

Frequent window cleaning

While washing dishes, splashes often fly, and there is no way to cope with this. But, if the sink is located at the window opening, then these drops will be much more noticeable on the glass than on the usual apron. This means that you will have to wipe it almost daily.

• choose a deep sink - so it will be more difficult for splashes to fly;
• put a mixer with a removable nozzle that directs the jet exactly on target - but such mixers are also more expensive than ordinary representatives.

Dryer

As mentioned above, you will have to look for a new place for a dryer for clean dishes: either put it in the lower cabinets of a kitchen set, or put a dishwasher.

Airing

If there is a window in the kitchen, this is a huge plus, but because of the decision to install a sink, this advantage can be lost.

Firstly, shelves and rods hung between slopes can interfere with ventilation.

Secondly, a large mixer may interfere with the normal opening of the valves. But the window will often have to be washed not only from the inside, but also from the outside, since traces of raindrops will constantly “calm” the eyes.

Another problem is that it can be difficult in principle for short people to reach the sash handle if there has been a large increase in the width of the window sill.

How can these problems be avoided? There are several options:

• make the sash not open at all;
• choose a small mixer - but then it probably will not have a nozzle, which means there will be splashes;
• put the faucet not in front of the window, but on the side or on the corner of the sink.

There is another problem that is difficult to deal with - dust. In the kitchen, a window is often opened to let out excess odors and heat. From the street, especially the city, dust flies right into the house. And if this is not so scary for the sink, then for the work area located next to it, or the dryer, which did not find a place above the sink, this is a problem.Eating dusty food from dusty dishes is not very pleasant. This factor can be neglected if the house is located outside the city.

Curtains

Not many curtains can be hung on a window that has a sink - because they will always be damp and greasy. Someone hangs a short tulle, as if they are in a Soviet dining room - this option is already outdated and does not look stylish.

The best option would be blinds or Roman blinds, but they are quite complicated and inconvenient to maintain. In addition, they are difficult to pick up: they can both decorate the kitchen and spoil its appearance.

What else to think about

After all the minuses and pluses have been sorted out, you need to think about some more points that may incline or, on the contrary, push away from the decision to do a sink next to the window opening.

Difficulty of moving

At a minimum, it is necessary to lengthen the water pipe and sewerage. As a maximum, it must be done correctly. Each additional linear meter of the pipe must be raised by 3-5 cm so that the water flows without obstacles and no blockages form.

If we talk about one meter of pipe, then it does not look scary. And if you need to pull the pipe through the whole room? Because of this, you may have to raise the sink to an uncomfortable height.

Another complication of moving is batteries. In typical Russian apartments, the battery in the kitchen is located directly under the window: if you close it with a countertop, then its efficiency will drop to a minimum.

You can make ventilation hatches, but sometimes drops will get into them, dampness and subsequently mold can form. In addition, due to the reduced efficiency in the kitchen, it will be colder than in other rooms. It is worth thinking about underfloor heating, but this will again require financial investments.

Alternatively, the battery can be moved. But this requires coordination with the UK (management company). So, the losses will be not only monetary, but also temporary. But even moving the battery will not solve the problem of heat, because in winter it will still be cold from the window, which is usually interrupted by heat from the radiator. Most likely, you will also need underfloor heating.

Height

If the window sill is low (up to 80 cm from the floor), then it will be extremely inconvenient to transfer the sink to it, since the optimal height for it is at a height of just 85–90 cm. with UK.

If the window is small and starts higher than 90 cm - there is nothing to worry about, you just need to arrange the transition from the countertop to the wall with a wide plinth. The sink will be literally "under the window".

Working triangle

The work triangle is a space where three things are done:

• wash;
• cut;
• cook - boil / fry.

The smaller this triangle, the better. If you move the sink to the window, and leave the work area on the opposite wall, then it will take much more time to cook, because you will have to “cut circles” around the kitchen every time.

tabletop

It is difficult to pick up a countertop under the sink by the window. If we talk about a tree, then it can be deformed when the temperature changes during the cold season - cracks may appear, and the original appearance will be lost. Therefore, it is worth giving preference to artificial or natural stone, but such a countertop will cost a pretty penny.

Are the windows suitable?

If there are windows with wooden frames, it is better to replace them with something more modern. An excellent choice would be a double-glazed window with plastic frames - it is not afraid of moisture and splashes, it does not deform over time and does not lose its attractiveness if periodically wiped with a microfiber cloth.

The kitchen layout with a sink by the window is perfect for really small spaces and a beautiful view outside the window. But besides beauty, there are also disadvantages, for example, the need to wipe the glass from splashes every day, the complexity of pipe wiring, and so on.

Is it still worth it to put a sink by the window? It is necessary to start from housing realities: most likely, such an arrangement of the sink is an excellent option for a summer house or a cottage, when designing which you can immediately take into account all the nuances. But the final decision is yours!

Advantages

Of course, the sink under the window has a number of advantages - otherwise such a solution would not have so many fans. The first thing that comes to mind is aesthetics. Yes, of course, while washing dishes or peeling potatoes, it is more pleasant to look at the street than at the wall. But is the view from the window so beautiful? And how long does it take to work at the sink? In addition to this ambiguous factor, there are several other advantages of a window sink that should be considered.

Lighting

In most cases, the sink is located in the corner or against the wall opposite the window, where additional lighting is required. Near the window, it is not needed in the daytime, and in the summer - until late in the evening.

For this reason, it is worth deciding on the time when you spend the most time in the kitchen: if during the day, you will win and save electricity, if in the evening, then you will most likely have to make an additional pendant lamp. Moreover, people from the street will be able to watch the process of washing dishes and peeling potatoes.

Space saving

A small kitchen is one of the reasons why people move the sink closer to the window opening. This is especially popular now in Khrushchev, where the kitchen area is only a few meters. So the place, "freed" from the sink, can be occupied by a working area or put the necessary equipment.

But here lies the downside. Typically, a dryer for freshly washed dishes is located above the sink. And with a window, this is impossible to imagine. It turns out that you will have to look for a place for a desktop portable dryer, or buy a dishwasher, which will lead to cash costs and require additional space.

Additional shelves

Sometimes, wanting to organize storage as efficiently as possible, people make shelves or hanging bars right between the window slopes. On the one hand, this is convenient, since the necessary items are at arm's length and even closer. But this will interfere with interaction with window sashes: their opening and cleaning will be difficult.

Moisture evaporation

Usually, washing dishes is not a big problem for the humidity around, but an open window nearby will allow you to quickly ventilate the room, get rid of moisture and excess odors.

Design solutions

Planning the interior of a kitchen with a sink by the window depends on many factors: the area of ​​\u200b\u200bthe room, the shape, the planned budget, the preferred color scheme. Rectangular rooms with a short side along the window opening are easy to approximate the shape of a square. To do this, the countertop with a sink is made wider.

Consider ideas that may interest connoisseurs of beauty even in the kitchen. Design solutions with a sink in the kitchen near the window are very diverse.

A wide wood-look countertop and a sink just to the side of the window. Cozy and good solution for a large kitchen space. The sink is quite deep, and the distance from the glass is maximum, which will not allow splashes to reach the window.

An overview of the sink in the kitchen near the window, as well as useful tips, see the video below.

Expert answers

OK:

You can transfer anywhere. It remains only to agree with her husband.

iRoman:

while the husband is against it is impossible

Azazella:

Lord, I would like your problems)

Releboy:

Of course you can - you can even go to a corridor or a room. It is only necessary to ensure the angle of inclination of the drain of the sewer pipes, otherwise they will be constantly clogged

Dmitry Pushkarev:

Within the kitchen, the sink can be placed without permission Even on the ceiling No problem

Alexey Pastukhov:

The hostess has a desire - this is already +, but to transfer the mona anywhere, I transferred it to the balcony ....

Grandfather Au:

firstly, you need to take kitchen sets on legs and a drain pipe is not a hindrance, secondly, moving the sink is no more than an hour and a half for a “teapot” when you have materials, you know what, but take care of this business yourself)) post a photo, and we will say how what what and how))

vlvics:

I endured it myself. So I ran the pipes around the ventilation duct through the bathroom with a toilet and connected to the common house riser. Under the bathroom it was hard to cut a hole in the wall, but slowly gnawed it out.

Alex Mishin:

From the sink to the sewer riser, in any case, a sewer pipe must go - after all, slop from the sink to the sewer cannot teleport through the 4th dimension. In addition, they must have a smooth slope - you cannot, for example, lay them under the floor and bring them up again in front of the riser. The pipes that bring water to the sink must also go somewhere. If the pipes laid from the sewer and plumbing to the new location of the sink will not interfere - then with God! I even once moved the toilet bowl to the opposite corner of the bathroom - and the sewer pipe goes to it with a diameter of 110 mm, and not 40-50 mm, like to the sink. You can read.

Docking thin (40-50 mm) PVC sewer pipes is quite within the power of a woman. For thicker pipes, man's strength is needed, even if the sockets are soaped before installation.

Uncle from the Future...

Nothing is impossible. The main thing you count is whether the slope of the sewer is enough for you. Take at the rate of 3 cm per meter. This is from where the sink now connects to the sewer. Under the sink, in a new place, the height of the drain is not desirable above 40 cents from the floor (so as not to get higher than the siphon). So count the pagonage of the canal, multiply by 3 and add the distance from the floor that is now. If it turns out no higher than 40-45 cm from the floor, then everything is fine. And there is no such problem with water - lead as you like, even under the floor ....

husky:

And you will excommunicate him for a week or two .... Well, my husband ... He will sing differently! He will carry this shell to you wherever you show with your eyes. Probably, sheds a mean male tear ....

Allegoriya:

The question is not clear. Pipes, of course, must be led to the sink)))

New day:

Moreover, in addition to water pipes, a sewer pipe is still desirable.

Just Olga:

Well, how else? Pipes in any way will go along the wall. After all, it will not be possible to mount it into it, since they did not do it right away. Think carefully about whether it is worth redoing everything, and most importantly, whether it can be done without coordination.

marina:

hammer a wall, or lead pipes, if not, then there is no third (

Alexander Bakushev:

make a box according to the height of the headset, and pull anything in it!

Anaida Zagoskina:

You will definitely need to lengthen the pipes. Use plastic ones. And the sewer needs to be installed. And you can hide it in a drywall box. You can make it permanent with windows or simply removable.

Scrapmaster Honored:

We usually go through the wall. In your case, it is not entirely clear why the pipes are in the hallway. Usually, they are located in the bathroom.

Farit Gafuanov:

when I lived in an apartment, I did it myself, I moved it to the opposite wall, I had to raise the floor in order to maintain a slope for the sewer

Rus Ivashkevitch:

Maybe. Lead pipes along the wall. The width of the countertop of kitchen furniture is 60 cm. The width (well, or depth) of the cabinets that will stand on the floor is 50 (52) cm. 8 cm remains behind the cabinets for pipes. Only a gas stove (or oven), if they stand before the sink), you need to look so that they do not run into the pipes from behind. There are no problems with water pipes at all - they are thin (you can take hoses for cold water - thermal insulation is necessary so that the pipe does not sweat). Sewer - there are 5 cm in diameter, and there are less (like 3 - 3.5 cm) - the throughput of both is enough. Good luck!

Larisa:

move it wherever you want, water pipes can be hidden in the floor, the channel can only be run along the wall and closed with a box

Application of additional fasteners

Corners are required to install the sink.

To fix the sink, you can use mounting angles and self-tapping screws. The first option is quite complicated, but all the necessary elements are included in the washbasin kit. The assembly process can be simplified because manufacturers of such structures offer step-by-step installation instructions.

The procedure is simple: the mounting plates will need to be fixed with self-tapping screws to the places indicated in the instructions. They need to be screwed in by about 5-6 cm. After that, it will be necessary to check the reliability of the connection and the tightness of the sink to the nightstand.

The sink can be fixed with wooden bars. This method is used when the bedside table has some defects or it is impossible to fix the sink with brackets. In this case, you need to first make an underframe from a bar, and then fix it with metal corners to the bedside table frame. The sink is installed from above, its location can be adjusted using a bar that is placed under the edges. There is another option, which is used if you can move the sink close to the wall. In this case, the screws must be installed into the wall surface through special holes that are located behind the sink.

Additional tips to consider when moving a sink

So that the sink does not cause trouble in further use, the transfer will need to be done by changing the level above the floor. This means that it will need to be raised by 4-5 cm per 1 m of transfer. For example, if the sink is displaced by 3 m, then it will need to be raised by 20-25 cm. If there is a large installation height, it is recommended to raise the base of the floor in the form of a podium.
A successful transfer of the sink is the location opposite the window, if possible. This arrangement can provide good lighting.
If there is a double sink, the drain system must be installed on both sinks, and the drain outlets are connected to a common siphon.
If the kitchen is large, then you can move the sink to the middle of the room.

The placement of the cutting table in the center of the room will look original.
It is important to check the coordination of the elements of the sewer system in the kitchen and bathroom so as not to drown the neighbors.

https://kuhnyamoya.ru/youtu.be/e4zSxkKdMf8

The kitchen is a complex system, where the installation of each of the elements is subject to certain rules. You can not install a sink in any place you like

Special attention should be paid to the supply of water supply and sewerage

In addition, it is important to observe the mandatory sealing of the joints. Transferring a sink is a rather complicated process, therefore it is important to take into account all the existing nuances.

The technology of work on the installation of an overhead sink

Scheme of installation of an overhead sink.

A sink of this type is transferred in the same way as a mortise sink, the only difference is in its installation.

Installing an overhead sink is much easier than a mortise one. During the installation process, it will not be necessary to cut the countertop, because a special bedside table with side doors is used, which does not have a top.

Installation work can be performed in several stages:

1. First of all, it is necessary to carry out preparatory work, which includes choosing a place to install the sink, buying a siphon and faucets. This will need to be done before installing the cabinet under the sink, because after installation it will be much more difficult to measure the pipes and install them. The ends of the tubes are best treated with silicone sealant so that the chipboard sheets are not sensitive to high humidity.
2. Next, you will need to choose the method of fixing the sink. In this case, you need to take into account the dimensions of the structure and their relationship with the opening of the nightstand. Today you can purchase a ready-made set of fasteners, as a result of which the question of choosing an installation method is eliminated. However, it happens that the sink and cabinet are bought separately. In this case, you need to make sure that all the elements are from the same manufacturer. You can fasten the structure as follows: with glue, corners for fasteners and a wooden beam. The first way is the simplest. The sides of the sink must be glued to the ribs of the nightstand, that is, you will first need to apply a special adhesive solution, and then press the sink until the mixture dries.

The technology works on installation of consignment wash

Scheme of the installation of shear washing.

Cleaning of this type is transferred in the same way as the flush sink, the difference is only in its installation.

Mount invoice sink is much easier than the mortise. During installation, do not need to cut the worktop, because it uses a special cabinet with side doors, which has no top.

Installation work can be performed in several steps:

1. First of all it is necessary to make preparatory work, which includes the choice of location for the installation of sinks, faucets and siphon purchases. It will need to perform before installing the cabinets under the sink, because after the installation of pipes to make measurements and perform their installation will be much harder. The ends of the tubes are best processed with silicone sealant to chipboard sheets were not sensitive to high humidity.
2. Next, you will need to choose the method of fixing the washing. In this case, you need to consider the size of the structure and their relationship with the hole tables. Today you can buy a ready set of fasteners, leaving the question of choice of method of installation is eliminated. However, it happens that the sink and cabinet must be purchased separately. In this case, you need to ensure that all elements are of the same manufacturer. To strengthen the structure as follows: with the help of glue, parts for mounting and wooden beams. The first method is the simplest. sink rim should be glued to the edges of tables, that is, pre-need to put a special adhesive mortar, and then press the sink until such time until the mixture is dry.

The use of additional fastening elements

To install the necessary cleaning corners.

To fix the sink, you can use the mounting brackets and screws. The first option is quite complicated, but all the necessary elements are included in the washbasin kit. The assembly process can be simplified, because such structures manufacturers offer a step by step installation instructions.

The procedure is simple: the mounting plate will have to be fixed with self-tapping screws to the places specified in the instructions. They need to tighten by approximately 5-6 cm. After that, it will be necessary to check the connection and close fitting sink to the nightstand.

Fastening shell can be made through the bars of wood. This method is used when there is some tables have defects or can not fix the sink bracket. In this case it is necessary first of all from a bar to make podstole, then fasten it to the corners of the metal frame tables. Sink is installed on top of, its location can be adjusted by means of a bar, which is placed under the edge. There is another option, which is used if the shell can be moved against the wall. In this case, the screws must be installed in the wall surface through the holes, which are located behind the sink.

Additional recommendations that need to be taken into account when transferring shells

1. To wash does not cause trouble later use, you will need to make the transfer, changing the level of the floor. This means that it will have to raise by 4-5 cm by 1m transfer. For example, if the shell is shifted by 3 meters, it will need to raise to 20-25 cm. If you have a large installation height, it is recommended to lift the base of the floor in the form of the podium.
2. The successful transfer of cleaning — a location opposite the window, if possible. Such an arrangement can provide good illumination.
3. If you have a double sink, drainage system must be installed on both sinks, taps and drain connected to a common siphon.
4. If the kitchen is large, it is possible to move the sink in the middle of the room. Originally will look occupancy cutting table on the center of the room.
5. It is important to check the coherence of the sewerage system in the kitchen and bathroom, so as not to drown neighbors.