9 Transport and storage
9.1 Valves should be transported by covered vehicles of any kind in accordance with the rules for the carriage of goods in force for each type of transport.
9.2 The conditions for transportation and storage of reinforcement in terms of exposure to climatic factors must comply with storage conditions 2 (C) in accordance with GOST 15150.
9.3 Fittings must be stored in unheated warehouses under conditions that exclude the possibility of mechanical damage, or in heated warehouses no closer than 1 m from heating devices with protection from direct sunlight and precipitation.
7 Acceptance rules
7.1 Rebar is accepted in batches. The batch includes products of the same type, made from raw materials of the same brand according to the same technological documentation, simultaneously presented for acceptance.
7.2 To check the compliance of fittings with the requirements of this standard, the manufacturer conducts acceptance, periodic and type tests. For testing, products are selected from the batch by random selection.
7.3 Types of control and sample sizes during acceptance tests are indicated in Table 2.
table 2
|
Controlled parameter |
Clause number of this standard |
Sample size per batch |
|
|
technical requirements |
test method |
||
|
1 Appearance. thread quality |
6.2.14—6.2.20 |
8.1.82 |
1% of the party, but not less than 5 sludge. |
|
2 Basic dimensions and maximum deviations from them |
6.2.9.6.2.20. figures 1-6 |
62 |
Also |
|
3 Closing density of the outlet opening with a stopper |
62.11 |
8.5 |
|
|
4 Electroplating quality and thickness |
6.2.18 regarding adhesion and roughness |
8.3 |
|
|
5 Tightness of siphon assembly |
6.2.10 |
6.4 |
1% of the party, but not less than 5 sludge. |
|
6 Fastening strength of cork and fishing line or chain |
62.11 |
8.6 |
For each new batch of fishing line. a new injection mold of the cork or after its repair. but at least once a month on five samples |
|
7 Material grades |
6.3.1 |
8.13 |
Each batch of raw materials |
9
GOST 23289-2016
7.4 Acceptance testing of plastic reinforcement should be carried out no earlier than 5 hours after its manufacture.
7.5 If, during acceptance tests, at least one product does not meet the requirements of this standard, a re-check is carried out for this indicator of a double number of products taken from the same batch.
In case of unsatisfactory results of the repeated check, the batch of fittings is not subject to acceptance. Piece-by-piece acceptance of fittings is allowed.
7.6 Periodic tests for compliance with the technical requirements of this standard according to 6.2.8-6.2.21.6.3.6.4.6.6.1.6.6.2 are carried out at least once a year on at least five samples.
7.7 If unsatisfactory results are obtained for any indicator, the manufacturer transfers tests for this indicator to the acceptance category until positive results are achieved on at least five batches in a row.
7.8 Type tests are carried out in order to assess the effectiveness and feasibility of making changes to the design of the reinforcement, its manufacturing technology, or when changing the composition of the raw materials. which may affect the technical and operational characteristics.
7.9 Fittings subjected to periodic and type tests are not subject to delivery to the consumer.
Foreword
The goals, basic principles and basic procedure for carrying out work on interstate standardization are established in GOST 1.0-2015 “Interstate standardization system. Basic Provisions” and GOST 1.2-2015 “Interstate Standardization System. Interstate standards. rules and recommendations for interstate standardization. Rules for the development, adoption. updates and cancellations
About the standard
1 DEVELOPED by the Open Joint Stock Company Scientific Research Institute of Sanitary Engineering (JSC NIIsantehniki)
2 INTRODUCED by the Technical Committee for Standardization TK465 "Construction"
3 ADOPTED by the Interstate Council for Standardization, Metrology and Certification (Minutes* dated August 31, 2016 No. 90-P)
Voted to accept:
|
Short name of the country according to MK {ISO 3166) 004-97 |
Country code according to MK (ISO 3166) 004-97 |
Abbreviated name of the national standards body |
|
Armenia |
AM |
Ministry of Economy of the Republic of Armenia |
|
Belarus |
BY |
State Standard of the Republic of Belarus |
|
Kyrgyzstan |
KG |
Kyrgyzstandarg |
|
Russia |
EN |
Rosstandvrg |
4 By order of the Federal Agency for Technical Regulation and Metrology dated November 11, 2016 No. 1678-st, the interstate standard GOST 23289-2016 was put into effect as the national standard of the Russian Federation from April 1, 2017.
5 INSTEAD OF GOST 23289-94
Information about changes to this standard is published in the annual information index "National Standards", and the text of changes and amendments - in the monthly information index "National Standards". In case of revision (replacement) or cancellation of this standard, a corresponding notice will be published in the monthly information index "National Standards". Relevant information, notification and texts are also posted in the public information system - on the official website of the Federal Agency for Technical Regulation and Metrology on the Internet ()
Standartinform. 2016
In the Russian Federation, this standard cannot be fully or partially reproduced. replicated and distributed as an official publication without the permission of the Federal Agency for Technical Regulation and Metrology
II
GOST 23289-2016
SANITARY CERAMIC PRODUCTS
TYPES AND BASIC DIMENSIONS
Official edition
INTERSTATE SCIENTIFIC AND TECHNICAL COMMISSION FOR STANDARDIZATION, TECHNICAL REGULATION AND CERTIFICATION IN CONSTRUCTION (ISTC) Moscow
Foreword
1 DEVELOPED by the Research Institute of Building Ceramics (NIIStroy-Keramika)
INTRODUCED by the Ministry of Construction of Russia
2 ADOPTED by the Interstate Scientific and Technical Commission for Standardization, Technical Regulation and Certification in Construction (ISTCS) on December 11, 1996
Voted to accept:
|
State name |
Name of the public administration body for construction |
|
Republic of Azerbaijan Republic of Armenia Republic of Belarus Republic of Kazakhstan Kyrgyz Republic Republic of Moldova Russian Federation Republic of Tajikistan Republic of Uzbekistan |
Gosstroy of the Republic of Azerbaijan Ministry of Urban Development of the Republic of Armenia Gosstroy of the Republic of Belarus Ministry of Construction of the Republic of Kazakhstan Gosstroy of the Kyrgyz Republic Department of Architecture and Construction of the Republic of Moldova Ministry of Construction of Russia Gosstroy of the Republic of Tajikistan Goskomarchitektstroy of the Republic of Uzbekistan |
3 INSTEAD OF GOST 755-82, GOST 21485.4-76, GOST 21485.5-76, GOST 22847-85, GOST 23759-85, GOST 26901-86, ST SEV 1002-78
4 By Decree of the Ministry of Construction of Russia dated December 30, 1997 No. 18-76, the interstate standard GOST 30493-96 was put into effect as the state standard of the Russian Federation from January 1, 1998.
5 REVISION. July 2006
IPK Publishing house of standards, 1998 Standartinform, 2006
This standard cannot be fully or partially reproduced, replicated and distributed as an official publication without the permission of the Ministry of Construction of Russia
to GOST 30493-96 Sanitary ceramic products. Types and basic dimensions
|
In which place |
Printed |
Must be |
|
Preface. |
from January 1, 19 of the Criminal Code |
from July 1, 199 |
|
Item 4 |
||
|
(IUS No. 11 2007) |
Ceramic sanitary ware. Types and principal dimensions
Introduction date 1998-07-01
1 AREA OF USE
This standard applies to sanitary ceramic (porcelain, semi-porcelain and faience) washbasins, washbasin pedestals, toilet bowls, flush cisterns, bidets, urinals and establishes their types and main dimensions.
Ceramic sanitary products are intended for installation in sanitary facilities, in amenity and other premises of buildings for various purposes, in sanitary facilities of river and sea vessels and railway cars.
The requirements of section 3 are mandatory, the rest are recommended, and can be specified by agreement between the manufacturer and the consumer (customer).
2 REGULATORY REFERENCES
This standard uses references to the following standards:
GOST 13449-82 Sanitary ceramic products. Test methods GOST 15167-93 Sanitary ceramic products. General specifications GOST 21485-94 Flushing tanks and fittings for them. General specifications
3 TYPES AND BASIC DIMENSIONS
3.1. Ceramic sanitary products (washbasins, toilet bowls, flush tanks, bidets, urinals) are made of the following types in accordance with the requirements of this standard according to approved working drawings.
Elements of the main products are given in Appendix A.
3.2 The shape of products is not regulated by this standard.
3.3. Washbasins
3.3.1 Types of washbasins
Washbasins are produced in the following types:
- semicircular, oval, rectangular, trapezoidal with or without a back;
- corner with or without a back and with or without overflow, with a cut corner;
- surgical and hairdressing without a back.
3.3.2 The main dimensions of semicircular, oval, rectangular and trapezoidal washbasins are shown in Figure 1 and Table 1.
Official edition
A A-A
4 Abbreviations
The following abbreviations are used in this standard:
SBU - unified bottle siphon with outlet and vertical or horizontal from
water for washbasins, sinks, sinks, bidets:
2
GOST 23289-2016
SBU2 is the same. for wash basins and sinks with two bowls;
STU - pipe siphon with a unified outlet, horizontal or vertical outlet for washbasins, sinks, sinks, bidets;
STU2 is the same. for wash basins and sinks with two bowls;
SVPG - siphon with outlet and overflow for bathtubs and deep shower trays;
SPM - siphon with outlet for small shower trays;
STUNS is a pipe siphon with a unified outlet, horizontal or vertical outlet for washbasins, sinks, sinks made of corrugated stainless steel pipe for high-rise buildings.
