Characteristics of soundproof tape
To protect metal frames from noise, during the construction of ceilings and walls, laying flooring, a damper tape is used. The rolled material is 30 m long, 10 cm wide and 3 mm thick. Surface density: 300 g/m2. The adhesive layer is applied on one or both sides of the tape.
Vibrostek-M soundproof gasket has the following characteristics:
- Compliance with the price of the material efficiency.
- Reliable protection against structural noise, despite the small thickness.
- Long operational resource.
- Resistant to various intense loads.
Tape sound insulation is not subject to deformation even under the influence of external factors and phenomena. The material has a number of characteristics:
- Zero water absorption.
- Resistant to oxidation, UV radiation, alkalis and weak acids.
- Elasticity and softness.
- Light weight (1 kg).
Vibroacoustic characteristics of the Vibrostek-M tape: dynamic modulus of elasticity 0.18 MPa at a load of 2 kPa; at 5 kPa - 0.35.
Possibilities of using Vibrostek-M
Soundproofing tape is used as a cushioning material when mounting:
- Panel system ZIPS in building structures.
- Wooden ceilings and floors.
- Frame soundproof linings and partitions.
When installing sandwich panels, the tape is laid in two layers at the points of contact with the ceiling and side walls, at the points of support on the floor. When installing frame partitions, sound insulation is placed between the fasteners and load-bearing building structures, at the junction of the sheathing sheets of the partition.
Vibrostek-M is used in the arrangement of wooden floors. The material is laid under the logs and floor beams - at the points of their support on the walls. The width of the tape must be greater than 10mm on each side of the beam or joist. Vibrostack is also laid on the ends of the beams, which rest on the walls.
Vibrostek-M soundproof gasket is indispensable for:
- When assembling various soundproofing systems (with and without a frame).
- In cladding and wall structures.
- When arranging suspended ceilings.
The tape is used as a border layer in the manufacture of a floating floor.
Sealing tape
Sealing substrates are made of flexible polyethylene foam. These are cellular strips covered with a self-adhesive layer on one side. They are protected by special paper, which is peeled off before use. Form of release of sealing strips - rolls of various lengths.
The material differs in brand, length and thickness of polyethylene foam. There are 3 varieties:
- Non-crosslinked gas-filled.
- Chemically crosslinked.
- Physically stitched.
Tape width varies from 30 to 90mm. The common thickness is 30mm.
Sealing gaskets provide a tight joint between the metal profile for drywall, as well as load-bearing structures - walls and floors. The tape is used not only for sealing, but also for vibration reduction and sound insulation.
The material is glued to guides through which sounds pass from one room to another. The rack profiles fixed to the walls are also pasted over with insulating tape.
Reinforcing tape
The reinforcing tape is indispensable for various construction works - repairing walls and ceilings, preventing the formation of cracks at the joints of gypsum boards, shedding, swelling, peeling of the cladding. In the structure of the tape there are interwoven fibers of strong material. Products are produced in reels, 50-100 meters long. On sale there is a regular and self-adhesive material.
Self-adhesive tape serves as an excellent electrical insulating material. It is used for waterproofing pipes, putty joints.Serpyanka is intended for reinforcing seams when performing finishing work.
Ordinary paper tape is used for sealing simple seams. Compared with serpyanka, paper reinforcing tape has significant advantages:
- A great combination with drywall and putty.
- Possibility of use when strengthening the prepared surface due to the minimum thickness.
- Acceptable cost.
The reinforcing tape is fixed with putty or gypsum plaster. Fabric and paper is characterized by good moisture absorption. PVC tape is moisture resistant.
Separating tape
Separating sealing tape is used in houses subject to strong shrinkage. The material plays a primary role in sealing the joints of drywall sheets. During construction and repair work, the separating tape is a component material for gypsum board along with jumpers, profiles, self-tapping screws, etc.
A tape separating gasket is required for a number of works:
- Metal profile fasteners.
- Tight sealing of seams between sheets.
- Fixing mounted partitions to ceilings and load-bearing walls.
Vibrostek-M materials are used for effective sound insulation. Due to the elastic properties of fiberglass and air pores, the vibration isolation tape has unique damping characteristics.
