Best Answers
Spruce oppression:
Triangular file.
FITA:
Try to screw in a thin crutch-plastic wall, into it a self-tapping screw or a screw. Then unscrew this design. but it is better to change the mixer.
Joanna Zalevskaya:
Pick up a screwdriver or chisel and drive it tightly into the broken piece and carefully unscrew it.
Airat Sattarov:
If it is broken from antiquity, then you are unlikely to get it - it has become attached tightly.
Grandfather Au:
You can try to unscrew the faucet with a 3-4-sided file, it will not help, then take a hacksaw blade, grind its end to half and saw through the thread to the tooth in 3 places - then remove the segments with a screwdriver
Alex Mishin:
Do you mean the flexible hose that connects the faucet to the water supply? And the fitting screwed into the body of the crane broke off? There is a special tool for this - a shank like a tap, the front end is a left-hand taper thread. But the sticky piece of thread would hardly have been able to turn them out either.
Looks like the faucet needs to be replaced...
Best Answers
Savior of Man:
Buy a bologna key for them and unscrew
Alexander Eremin:
Remove mixer...
salim ahmedov:
10 or 8 key try to unscrew
Can't find the fire?
Disconnect the hoses on the other side, unfasten the faucet, pull it out and unscrew it.
grandfather mikhey:
cut off the hose and buy such a key ... it costs 70 rubles ..
Spitz Pomeranian:
The open-end wrench must be heated and bent, and then the mixer can be removed.
Tula:
Tear off the hose and end ....
Igor Larin:
VDshka help you
Alexander Vakhromov:
I join D. Mikhey and here is also an option
Alesya Finikovskaya:
take off your panties
Cat smile:
Assemble the mixer with pipes - then install it on the sink, there is 1 central nut for 10 or 12mm. Therefore, you need to unscrew this central nut, remove the mixer and there will be access to unscrewing the hoses. Already advised, just cut the tube - oh yay yay, no need) ... The key-tube end 10 x 12 mm MATRIX, and it's not expensive, you can unscrew it. .shuruping /collection/klyuchi-gaechnye-tortsevye/product/33211
Przhevalsk:
try with a wrench
Sergey Shumov:
There are taps in which the hoses are rotated, but fundamentally not unscrewed. Perhaps you have had this case? What is the model of the crane?
Starr Grandfather:
There are such firms, they do it on purpose, so that they can be twisted without a key. (eg AM-PM) But such occasions happen. Cut off the hose and turn it out with a socket wrench at 11 in the pictures (for Mikhey and the cat) You can’t unscrew it with a cap (like Alexander’s).
Alexey Burdakin:
I had a similar situation, got angry, cut off the hoses, inserted a flat screwdriver into the hose and, surprised myself, but it went like clockwork.
Expert answers
Michael:
if you reach out, you need to grab the rim around the hose under the mixer with pliers and turn it off and buy one in the store, just not cheap, screw it back with your hands and pull it with pliers, but not very tightly (sometimes it’s enough to tighten it with your hand0 and then screw it to the pipe with a wrench. To do not pull the pipe too much, otherwise you will pull the nut and it will burst, maybe not immediately.Yes, just first unscrew it from the pipe, if the woman does not have an adjustable wrench, then you can use large pliers to wrap around the nut.PS, unscrew the nut, perhaps if the mountain. the water will go hard, make sure that the valve that shuts off the water does not turn, and look at the condition of the pipes and valves, if they are rusty and don’t spin, then it’s better that Maria said correctly, don’t climb yourself
Vitalban1:
Buy a new one - the higher its price, the quieter it works. All plumbing equipment is designed for a maximum of 5 years, buy a new one, than you will suffer with this mixer in six months. the cartridge or bushings will be covered.
Maria:
Call the plumber, otherwise you will flood all the neighbors. And they unscrew it with a special key, and the diameter of the pipes is different, they wouldn’t climb where you don’t know, it will only come out more expensive.
BOSS:
Key number 11. GO!!! What is included in the mixer. Buy the same one that was unscrewed ...
Valery Golda:
turn off the water, choose a nag that is suitable in size, unscrew both hoses, buy the same ones and put them in place
Ermak Group:
Very simple. Unscrew the hoses only from the side of the mixer, and from the side of the pipe - do not touch.
konmal:
It will not work if thin pipes fit to the mixer. They don't spin.
gray-haired:
experiments begin in the morning .. and the fact that there are the basics of plumbing is for x ... y!
Veretragna Mitra:
First you need to pull the mixer out of the sink, otherwise it will be inconvenient. Well, on the merits of the matter - there are hex fittings at the ends of the flexible hoses, unscrew them for them
Arkady:
I'm sitting, crying. Yep, hexagons. Only two problems. Getting to them without removing the faucet from the sink is difficult. And secondly, how will you twist them? The nut, slightly loosened, begins to turn. It's easy to open. But the hexagons with the hose are tightly connected. You have to twist the hose. Most likely you will ruin it.
Expert answers
Arkady Trubetskoy:
Take the key and turn it off.
Cat smile:
... It’s boiled over - you have no other choice but to rip these off and throw them in the trash - by the protruding ends, with platypuses - you will turn it out., - Then you buy others with a LONG shank - for these just options - you don’t need to twist it much, there the gasket is reliable - and unscrew - a long shank allows ...... Py. Sy. you can contrive - and throw nylon clamps inside - tighten and unscrew for them - but the option is that this eyeliner is unusable - 90%
Alexander Doronin:
cut off the braided hose, what remains to be tightened with pliers. pick up a tubular wrench or a head with thin walls
Hero of the day:
Key.
Dmitry:
The mixer is not Oras for an hour? If Oras - then there is a left-hand thread on the eyeliner: to turn it out, you need to turn it clockwise. If it doesn’t work with your hand, then there is an internal hexagon in the eyeliner. Take out the cartridge and unscrew it with a hex wrench.
Just a king:
Unfortunately, what we see in the photo is hopelessly sent to the trash can. There's nothing to fix there. Need a new mixer. The eyeliner can be left as is.
Obormot cat:
Try to heat it with boiling water from the kettle and then unscrew it until the internal thread has warmed up.
Ravshan Buzoev:
WD forty nanonight or kerosene - then wrap it with a rag tuko and twist
Podzhopnikov (s):
What, turn off the hot water?
Volkov Vladimir:
take a rag
Alexander:
if it’s not glossy and it’s not damaged, you can knock on the nut a little ...
Gossamer:
Ask a neighbor for a key.
Alexey Zolotov:
we wind two sticks on one side with a rope;
Natalya Klemyatich:
In the stick, they drank a groove to fit and unscrew
The choice of eyeliner
If you need to replace the flexible hose, then first of all you need to choose the right hose to connect the mixer. When choosing, you need to rely on the following factors:
eyeliner assignment. On sale you can find hoses for connecting cold and hot water, as well as universal products. The cold water inlet is wrapped in blue thread. For hot water - a red thread. Universal eyeliner has interspersed with both blue and red threads;
Connection suitable for connecting both cold and hot water
In order to avoid misunderstandings, experts recommend using a universal eyeliner to connect the mixer.
hose settings. When selecting parameters, it is necessary to determine the type of connection of the supply to the mixer and the water pipe (nut, fitting, and so on), as well as the type and size of the thread. The thread is internal and external. Thread sizes range from ½” to 1 ½”. The next step is to select the length of the hose. To make the connection as reliable as possible, it is necessary to eliminate the possibility of stress on the hose. This requires choosing a device whose length is slightly longer than the distance from the mixer for pipe outlet;
Selection of eyeliner by type of connection
- material for the manufacture of fittings and nuts. Brass is more reliable and durable.The connecting elements can also be made of aluminum (over time, the material becomes rusty and becomes unusable) or plastic (highly susceptible to mechanical stress);
- the hose must be flexible enough. If, when holding the eyeliner at one end, the hose takes a hanging position, then this indicator is normal. If the hose assumes a horizontal position, then the elasticity of the product is small;
- there should be no visible damage on the winding, nuts and fittings, which will lead to a reduction in the life of the product.
Based on the presented factors, each user can independently choose the most suitable and durable product.
