Izolon

How to glue isolon to concrete

how to glue isolon to concrete

In the construction of industrial facilities and residential buildings, modern building materials are used to meet the most important building requirements for heat and sound insulation. Such material, for example, is isolon or foamed polyethylene foam. The use of isolon reduces construction time and heating costs due to the excellent thermal insulation properties of this material.

Isolon has the following characteristics 1. Low density (light weight) and at the same time good thermal insulation properties. A layer of isolon 10 mm can replace a layer of 15 mm mineral wool, 45 mm wood or 150 mm brickwork.

This reduces the mass of structures and helps to save usable area, 2. In the production of isolon, freons and other substances dangerous to humans are not used. Izolon is non-toxic, does not affect the skin, does not emit harmful substances when applied. Has a hygienic certificate, 3.

Isolon is a chemically inert material, it is not affected by organic solvents. It is possible to combine isolon with other building materials (concrete, gypsum, cement, lime, wood). It practically does not absorb water and steam, therefore it is resistant to decay, mold and aging, 4.

Excellent shock-absorbing properties due to flexibility and uniform cellular structure. Isolon is used as a substrate for carpet, laminate, linoleum or parquet. Isolon sheets are used to separate adjacent walls, if adjacent walls are subject to movement or vibration, 5. The operating temperature range is from -60`C to +75`C, and if there are no mechanical loads, the working temperature increases to +100`C. With the exception of special isolons with fire-extinguishing additives, isolon is a combustible material. But at temperatures less than + 140`С, no harmful substances are emitted from isolon, 6.

Izolon is produced in different thicknesses and densities (with different foaming ratios) and is supplied in the form of rolls, sheets, tapes or blocks. This greatly increases the possibility of using isolon in construction. Depending on the production method, isolon is divided into cross-linked (when molecules are cross-linked, a network molecular model is formed) and non-cross-linked (there are no chemical bonds between polymer molecules).

Cross-linked isolon has improved characteristics compared to non-cross-linked isolon 1. Increases heat resistance (working temperature range increases by 20`C), 2. Increases the service life of the material due to increased resistance to ultraviolet radiation and organic solvents: oil, gasoline, diesel fuel, Izolon can be used one.

For sound, steam, heat, waterproofing of walls, foundations, ceilings and roofs for country houses, cottages, garages, 2. As a sealant for slate, ribbed metal roofs or tiles, 3. Insulating tapes with an adhesive layer seal the joints of windows and doors, connections between the frame and glass, protect against dust, moisture and noise, 4. Izolon strips can be used to insulate cold and hot heat supply pipes, as well as ventilation pipes, 5. Izolon with a polymeric metallized film is used as a heat-reflecting screen to protect against heat loss through the radiator sections of the walls. When using a combined material, a double effect is obtained.

Due to the metallized film, up to 90% of the heat emitted by radiators or other thermal devices is reflected back into the room. A big plus of isolon is the ease of its use and installation. It is easy to cut and can be glued to the surface with adhesives (preliminary glued surfaces must be cleaned of dust and degreased).

To attach to a smooth surface, use screws, rails, furniture staplers. To connect the joints, use a building hair dryer.Isolon is attached to curved surfaces with double-sided mounting tape.

Thus, when using this modern material, it is possible to significantly reduce the construction time and heating costs.

How to glue isolon to concreteHow to glue isolon to concrete how to glue isolon to concrete In the construction of industrial facilities and residential buildings to ensure the most important building requirements for heat and sound insulation

Secret. How to glue foil insulation to the wall.

Kind. Somehow I ran into a problem with gluing foil insulation to the wall. There is a lot of information on the Internet about this. But how and with what glue I did not try - in the end, nothing happened. Everything fell off. And the secret is simple. The insulation is covered with a thin polyethylene film, to which the glue does not stick (to a smooth surface, it has nothing to catch on). The manufacturer did not take this into account, or did not want to. It is enough to make the places where the glue is applied, rough, that is, for sanding with sandpaper. You can use any glue, as well as mounting foam. And you don’t need a stapler, nails, dowels, military-strategic poisonous liquids - as mentioned in many construction forums. Good luck everyone, keep it up.

Small observation. But many do not see the little things. Hence the big problems.

It is enough to make the places where the glue is applied, rough, that is, for sanding with sandpaper.

And most importantly - why spend money on this and other materials and stick something that will not bring any effect.

jekasus wrote: And most importantly - why spend money on this and other materials and stick something that will not bring any effect.

I will support. Apparently, the TS simply has free material and time must be killed.

jekasus wrote: And most importantly - why spend money on this and other materials and stick something that will not bring any effect.

Yes, I agree with you. But this effect is not in the preservation of heat, it is enough, water heating comes from the house. If you take a closer look at the last photo - this is an extension of the future greenhouse on the north side, of course there will be not enough light for plants. Reflective paint is not available. Here is the foil to reflect it. Even with artificial lighting, entering the room at night it is not possible to look, the eyes are hurt by a bright, dazzling, iridescent light. (Checked, a few light bulbs are enough) That's a plus for energy saving. In general, the issue was not considered on the construction of greenhouses and where, why glue the foil insulation. The meaning of how to stick!

How to fix isolon to the wallKind. Somehow I ran into a problem **glue** foil insulation to the wall. There is a lot of information on the **Internet** about this. But how and with what glue I have not tried - in ... - photo- Mastergrad Forum

Neoprene Sportswear

Products for the back | Products for upper limbs | Products for the lower extremities |
All products

Products for the back

Neoprene lumbar brace

Article: 4200.

The bandage provides fixation, protection and stabilization.

Products for upper limbs

Neoprene wrist and thumb brace

Article: 4607.

The bandage is made of neoprene 3 mm thick.

Neoprene wrist brace

Article: 4603.

The bandage is made of neoprene 2 mm thick. Bandage can
use on both hands.

Bandage for epicondylitis neoprene

Article: 4302.

The bandage is made of neoprene 3 mm thick with adjustable
Velcro fastener.

Neoprene wrist brace

Article: 4600.

The bandage is made of neoprene 3 mm thick with adjustable
Velcro fastener.

Neoprene elbow brace

Article: 4304.

The bandage provides fixation, protection and stabilization of the elbow
joint.

Neoprene wrist brace

Article: 4603.

Bandage 3 mm thick with a palm rail and Velcro straps.

Neoprene shoulder brace

Article: 4801/4802.

sleeve-shaped neoprene bandage, secured with a strap that passes under the opposite arm and secured with a clasp.

Products for the lower extremities

Neoprene knee brace with open patella

Article: 4119.

The enveloping detachable orthosis provides fixation, protection and stabilization of the ligamentous apparatus, soft tissues.

Neoprene ankle brace

Article: 4405.

The bandage provides fixation, protection and stabilization of the ligamentous apparatus, soft tissues.

Neoprene knee brace with reinforced side and silicone patella ring

Article: 4106.OR

The lining of the brace is made of breathable porous material, the outer material is velor (both materials are elastic).

Neoprene patellar fixing bandage

Article: 4110.

Neoprene patellar bandage with compression pad.

Neoprene knee brace

Article: 4111.

Bandage thickness 4.5 mm. The kneecap is open.

Neoprene ankle brace with criss-cross straps

Article: 4401.

The bandage is made of neoprene, 3 mm thick.

Reinforced neoprene ankle brace

Article: 4406.

The bilateral bandage is made of neoprene, 3 mm thick.

Orthosis on the thigh

Article: TP-4500.

The orthosis consists of two thermoplastic plates covered with velor fabric, which can be easily removed for washing.

Neoprene shorts

Article: 4700.

The shorts are made from 2mm thick neoprene.

Neoprene ankle brace

Article: 4800.

The tapered bandage is made of neoprene 3 mm thick.

Best Answers

Grandfather Au:

ordinary food will not work - it’s metal, and if it can “reflect” some part of the radiation, then part of the convective flow will still heat it, and since aluminum is an excellent conductor ... Under the foil you need a heater! The walls themselves need to be insulated, for example .termoplex /korund.php?table=korund

*:

Try to stick with saliva ...

Marek Black:

You better insulate with pinoplast from the outside. and the floor can be insulated. You talk to those who do it.

Evil Electrician:

I think you need to consult in the building store or try the moment of installation

New:

First, prime several times with betonite, and then glue, but it is better with a heat-insulating layer, at least on PVA, but there is something that is already sold as a self-adhesive on a heat-insulating substrate.

Sergey Burmasov:

think maybe iron galvanization, but stainless steel is better because foil is weak

nina ilina:

oh, if you stick it crookedly, the receiver is a magnifying glass, with a focus like the fleet was burned in ancient Greece)

Albert Belkov:

I use Termoizol - foil on foam, it's easy to work: I insulate steel bathtubs - they turn out to be no worse than cast-iron ones, they are warm. And the food can be glued on cardboard with slots for hooks to easily insert.

Yuri Martysyuk:

Buy penofol, sold in different thicknesses. It can be self-adhesive, and if not, try double-sided tape!

Chuck Casemerczak:

If the foil sticks to the glass with egg yolk, then it will definitely stick to the concrete

How to choose glue

On sale there is a fairly wide range of various adhesives for working with polyethylene foam. And the choice is expedient to carry out, using the following criteria.

• The temperature range must match this characteristic of the insulation.
• Adhesion properties must be extremely high.
• If the adhesive is planned to be used for interior decoration, then it must be certified and non-toxic.
• If the adhesive is chosen for exterior decoration, then it must be resistant to a variety of weather conditions and temperature extremes.
• If you intend to finish the sauna and bath, then the glue will need to be mixed with water-repellent agents.

Water-based glue is not categorically suitable for working with isolon, because it does not allow the adhesive to penetrate into all the pores of the insulation. Therefore, the level of adhesion will be insufficient.

Baths

Energofol heaters, having a protective layer of aluminum foil, are placed under the interior lining of the room (foil inside). These materials are designed to resist heat without emitting any odors or harmful gases.

Energofol materials are also used for thermal and sound insulation of refrigerated containers and insulated bodies, for air conditioning systems (as an air duct insulator) and pipeline systems. In residential premises, they are laid between the wall and the heating radiator.

Materials are ideal for roof and attic insulation. Roof mounting is identical to wall mounting. The material is attached to the rafters from below, with an aluminum layer inside the room. When using materials with double-sided coating, an ideal microclimate will be maintained in the house at any time of the year.

The use of Energofol coating in the heating system "warm floors" leads to:

• reduction of energy costs;
• reduction of floor heating time;
• reducing the heating of the ceiling of the apartment located on the floor below.

1. Maskizol
2. overlap
3. A heating element
4. Cement-sand screed
5. Ceramic tiles, linoleum, carpet

To increase the efficiency of the "warm floors" system, materials with a thickness of 3 mm, 5 mm, 10 mm are used. The material is placed under the heater with a reflective surface in the direction of the room. The material Energofol reduces heat losses that go to heating the underground space, evens out the temperature field of the apartment.

When insulating the floor with electric heaters, you must carefully follow the electrical safety requirements, since aluminum foil is an excellent current conductor.

In addition, Energofol is perfect for a “floating floor” device (when the thickness does not exceed 3 mm), when installing underfloor heating located above a cold space, as well as when insulating the floor “along the guide logs” (material is laid between the logs).

1	Energofol A2	sq.m.	from 21 r	Heat and steam sound insulation of walls, floors from -50 to +100 C
2	Energofol A3	sq.m.	from 22 r	Heat and steam sound insulation of walls, floors from -50 to +100 C
3	Energofol A4	sq.m.	from 23 r	Heat and steam sound insulation of walls, floors from -50 to +100 C
4	Energofol A5	sq.m.	from 28 r	Heat and steam sound insulation of walls, floors from -50 to +100 C
5	Energofol A8	sq.m.	from 38 r	Heat and steam sound insulation of walls, floors from -50 to +100 C
6	Energofol A10	sq.m.	from 46 r	Heat and steam sound insulation of walls, floors from -50 to +100 C

Foil insulation for walls and floors

Insulation with foil relatively recently appeared on the construction market, but is rapidly gaining popularity for various reasons. Next, we will consider the types of this material, the advantages in comparison with traditional heaters and how to use it correctly.

What is rolled foil insulation

This is a combined material for the insulation of walls, floors and ceilings, consisting of several layers:

1. Insulation made from conventional materials.
2. foil layer.

The material is rolled, therefore it has a relatively small sheet thickness. What is heat retention?

• A thin working layer delays the penetration of cold air from outside,
• The foil reflects the heated air into the room.

Varieties

Roll heaters are classified according to the main material:

1. Polyethylene foam with foil that can be attached on one or both sides.
2. Folgoizol is created on the basis of bitumen / rubber, mineral fillers and an antiseptic.
3. Mineral wool rolls with one-sided foil surface.
4. Basalt lamellar heaters,
5. Expanded polystyrene boards with one aluminum surface.

Each of the presented materials is intended for use in certain conditions.

Application

Penefol (closed-cell polyethylene foam) is versatile in use. They isolate walls, floors in residential premises.

Foil insulation for pipes and roofs - foilizol.It is also used in the construction of industrial facilities.

Rolls of mineral wool with an aluminum layer are used in the same way as conventional insulation mats: for insulating walls, floors and other structures. The difference between foil mineral wool and ordinary wool is built-in waterproofing, aluminum does not let moisture into the fibers, preventing the material from getting wet.

An ideal foil insulation for a bath based on basalt: it has a low heat transfer coefficient, is not afraid of humidity and large temperature changes. As you know, stone wool is a hard material. To roll it into a roll, basalt is sawn into lamellas, and they are laid on an aluminum base. This insulation is used to isolate various social and industrial facilities.

Foiled polystyrene foam is used for floor insulation.

All materials with an aluminum foil interlayer have a higher technical performance than their traditional form. The cost of foil insulation is an order of magnitude higher than the cost of conventional material, this is the main drawback of the "advanced" sample.

The first and most important question is which side to put the foil insulation on?

The first rule of laying: the reflective side should be directed towards the room. This will provide natural heat reflection.

We insulate the walls

The structure of insulation and finishing should be thought out: between the insulation and the subsequent finishing, in the case of walls, there must be an air gap. When using a mineral wool base, it is necessary to isolate the material from water penetration; for this, a membrane is attached to the base, which allows steam to pass out.

How to fix the foil insulation to the wall: an insulator is rolled out over the fixed membrane and fixed with guide rails, the thickness of which should exceed the thickness of the main insulation. The layers are connected with staples along the edges of the rails. The subsequent finishing of panels or lining is carried out along the guides, which provide an air gap with their thickness.

Some craftsmen recommend protecting the foil with vapor barrier films to prevent moisture from entering the body of the mineral wool layer through possible holes in the metal.

We warm the floor

For wooden and concrete floors, the algorithm of actions remains identical:

1. The base is cleaned of old coatings, garbage is carefully swept away.
2. Prime the subfloor with a primer for concrete or wood.
3. After the primer dries, measure the required amount of rolled insulation and roll it out. It is optimal to use an adhesive-based material. The strips are overlapped by 10 cm, the joints are glued with aluminum tape.
4. Lay top coat on top.

If the room has an electric or water "warm" floor, the rolls are rolled out with the reflective side up, a reinforcing mesh is laid on top, then heating elements and a cement screed is produced, followed by cladding.

Foil insulation for walls and floorsConsider the types of foil insulation, the advantages in comparison with traditional heaters and how to use it correctly.

Expert answers

Anatoly Bondar:

.Moment. Apply in thin strips and stick

Vladimir Petrov:

Any house that has everything to keep will only not be a clerical one. Liquid nails or wallpaper glue work well

BASIL:

double sided tape is good

Scarifier:

The most accessible and inexpensive BF-2, glues metal to organic.

Roman Shved:

Nothing but a stapler. Fall off. Checked multiple times. And food will not work. Look for foil for baths and saunas, preferably on kraft paper, here it can be glued with glue. Do not stick clean foil.

Special opinion:

why? if for thermal insulation - foam plastic is better, for sound insulation mineral wool is better

User deleted:

do not glue, but pin. Reikami. Put an isolon, a rail on it evenly and drill holes, fasten it.And so every 50 cm. Well, or vice versa - first the slats with a "lattice" to them isolon. Is it really so difficult to figure it out? Why is it necessary to "glue"? It is POSSIBLE to glue anything other than stone or concrete to concrete. Fuck off. Or condenses and dump.

By the way, the dissenting opinion is right - a lattice of slats with mineral wool and close with drywall or plywood on top. Much better.

Emir of Bukhara:

it is also self-adhesive - prime the concrete with any interior primer, let it dry for 12-24 hours and stick it on - and if it is not foil-coated, then you need to buy foil-coated - if not, then glue for linoleum like 88 I don’t know what it’s called, but the effect is one thin layer on one and on the other surface and glue

Orest Postal:

You need to know the strength of the concrete slab. try contacting the professionals who work with them slav-beton /index.php?id=2 I'm sure you will be given advice on how to do this, or they will do your work for you. Good luck to you

How to fix reflective insulation on a concrete wall

How or with what can reflective insulation be glued or attached to a concrete wall? Thank you.

Reflective insulation is called a light, flexible material with a thickness of 4 mm or more, consisting of a layer of foamed polyethylene or other polymer, on which aluminum foil or metallized film is glued on one or both sides. Foil thermal insulation materials are environmentally friendly, easy to install and significantly reduce heat loss.

Manufacturers of reflective thermal insulation materials do not exclude the use of glue during installation, but they draw the attention of consumers that they are most effective if an air gap of 2 to 10 mm is created between the wall and the thermal insulation. After all, air is also an additional heat-insulating layer.

The method of attaching reflective thermal insulation to a concrete wall is chosen depending on the type of material, possibilities, location and purpose of the room. In any case, the concrete wall must first be cleaned of dust and treated with an antiseptic, and if necessary, dried.

When insulating balconies or cold external walls with a heat insulator with a double-sided foil coating, it is necessary to fill a crate of slats with a thickness of 5-7 mm on concrete and fasten the material to it with a construction stapler or glue. A second crate is mounted on top of the heat-insulating material for laying with an air gap of the finishing coating.

When mounting on reflective materials with a one-sided metallized coating, it is allowed to use adhesives based on rubber or acrylic, such as 88-NP, Akrol contact, Neoprene 2136 spray, etc. You can also use mounting foam, sealing sealant and double-sided reinforced construction tape . The adhesive composition is applied on the reverse side of the material dotted in a checkerboard pattern or randomly, so that after gluing to concrete, the required air gap of about 2 mm remains.

Cloths of reflective insulation are glued end-to-end and the seams must be glued with aluminum tape. As a result, an airtight coating is created on the wall, resembling a thermos, on which you can mount a lath crate for attaching a finishing material.

Finally, if an increase in the thickness of the walls is undesirable or impossible, self-adhesive foil heat-insulating material can be used for insulation. For its installation, it is only necessary to prepare the concrete surface and remove the protective film from the wrong side of the web, and after gluing, seal the joints with foil tape. But when fastening to the crate, the efficiency of self-adhesive metallized insulation is higher.

How to fix reflective insulation on a concrete wall?Tips on how to fasten reflective thermal insulation to a concrete wall, depending on the type of material, purpose and possibilities of the room