Noisy new single-lever mixer

Faucet failure

This may also be one of the reasons why the tap starts to buzz when the water is turned on. It should be noted that this is the simplest problem that is fixed in a matter of minutes. Diagnostics can be carried out independently, for this, open the tap and observe. If the pipe starts to vibrate, then either a faulty mixer or a shut-off valve is to blame. To solve this problem, it is necessary to turn off the water in the riser and proceed with a simple repair.

Most often, in this case, the cause is simply a worn gasket. Remove the valve and carefully inspect it (the gasket is located at the end of the stem). If it has taken a pointed shape, it is necessary to replace it. After that, we assemble the structure and put it in place. After this procedure, the noise should disappear. We add that this only applies to old mixers that are equipped with crane boxes. If you have a modern single-lever or then look for the reason in another. In these designs, the gasket that blocks the flow of water is simply absent, so it cannot be the cause of noise in the pipes. By the way, if you still decide to disassemble the tap, you can immediately change the mixer to a more modern one.

Poor or poorly done repairs

Understanding, when you turn on the water, you first need to remember whether you have recently repaired plumbing equipment. If the answer is no, and the noise is repeated, then you need to find out if one of the neighbors recently carried out any work. In addition, you can call the service organization (housing and communal services), perhaps the plumbers, working in the basement, poorly connected the elements.

If you find out that such actions have taken place, then this may well be the reason why the tap is buzzing when the water is turned on. However, we'll fix it. Eliminating the buzz is not difficult. Poorly fastened pipes are fixed, and the hum disappears instantly. However, this may not be the only issue. If inexperienced plumbers have placed pipes very close, then vibration will inevitably appear. In this case, there is nothing left but to wrap each of them with foam insulation.

in system

And we continue to talk about why the tap is buzzing when the water is turned on. One reason could be overpressure. You can determine it by the pressure of the water, it is usually very good, and when the tap is fully opened, the jet bursts out with noise and hiss. There is another way to diagnose. The buzz may appear if you open the faucet quickly. In this case, you need to take time for this problem, or even better, call a plumber to assess the situation.

Why is this phenomenon dangerous? The fact that it can lead to depressurization of the system. Moreover, you cannot reduce the pressure yourself, so you have to come up with something else. To reduce the load, you will need to install an air chamber. It is she who will dissipate pressure, as a result of which the rumble will stop, and you can breathe freely.

toilet tank

The toilet tank is another reason for unnecessary noise in the apartment, let's take time for it. Usually, when assembling the drain structure, a tube is placed on the inlet valve, which at one end drops almost to the bottom of the tank. When the water in the tank begins to fill and the tube closes, the noise disappears.

The reasons are as follows:

• the tube fell off;
• it was not installed during assembly for some reason.

How to fix the situation:

1. Just put the handset back if it has fallen off.
2. For the second reason, you need to choose a suitable piece of plastic or rubber tube and install it in the drain tank.

In this article, we looked at the main causes of extraneous plumbing noise.All repairs can be safely done by yourself, or you can call specialists in the plumbing field, they should do everything perfectly. Since the pipeline is not the last cause of floods, you should not forget about it, because from time to time its parts wear out and they should be replaced. Do not skimp on such things, because if the irreparable happens, it will be too late to think. You will have to shell out much larger sums for major repairs, perhaps not only the bath, not only yours.

Residents of apartment buildings know firsthand about this phenomenon. Sometimes it is a barely audible hum, and sometimes it is felt throughout the riser or house. Today we want to talk about why the tap is buzzing when the water is turned on. At first glance, this is not a very serious problem, but sometimes it causes certain inconveniences. Let's figure out why this problem occurs and what methods exist to deal with it. There are many theories that explain why pipes hum. In practice, plumbers identify four main reasons that cause this phenomenon.

What to do so that the faucet does not buzz

To determine the type of faucet-axle valve mixer, you need to pay attention to the following. If the mixer valve turns only half a turn, a ceramic element is installed in it

If you need to turn the valve several times to turn on the water, the mixer has an ordinary axle box with a rubber gasket. To eliminate noise in a conventional faucet box, you must first completely shut off the water supply. Then it is necessary to remove the valve from the axle box, for this it is necessary to unscrew the special bolt. After that, the axle box is carefully unscrewed. The gasket that has become unusable must be replaced with a new one.

The reason for the noise in a faucet with a ceramic insert is the silicone washer. It is used to “push” ceramic rings into the correct position. In this case, it is better to replace the ceramic insert with a new one. Noise in a lever mixer most often occurs due to pressure drops in the pipes. To normalize it, you need to install a special reducer on the water supply system that allows you to control the pressure level. This device limits the pressure to 2.5 atmospheres, after which the noise in the pipes stops.

• Causes of the problem
• water pressure
• Crane repair
• Rubber gasket
• Ceramic gasket

Many have experienced the phenomenon when the hot water tap is buzzing. It is almost impossible to give an exact answer why it occurs. Various factors can influence this. Any reason can be justified from the point of view of acoustics and hydrodynamics. By finding out the cause of the occurrence, you can fix the problem.

If your tap is buzzing, then immediately, in order to save money and save your nerves, you need to eliminate the cause.

Best Answers

Viktor257:

change the rubber band on the faucet..

Maxim Afanasiev:

If we proceed theoretically, then from the air it happens like this for a year, the water is turned off and the tap starts to whistle, buzz and spit

Sergei:

This is due to a faulty faucet box in the mixer

konmal:

Change the kranbuks to ceramic ones.

Vladimir Petrov:

Change gasket or bushing valve

Natalya Klemyatich:

Right now everyone is buzzing ... from time to time

XsaVis:

There is a rubber band on the faucet. Inside. Open the thing. Insert a rubber band. Sold in a plumbing store. In the store, ask the same thing as here. You will be prompted.

Cheshire cat:

Change the valve, if water is leaking (drips from the faucet), if not, then invite a plumber, the symptoms are similar to the airiness of the riser.

Nikita Nikitin:

Gasket wear.

Pasha:

Crane hurts from something

Denis Garan:

put ball joints, they don't hum

Why is the faucet making noise in the kitchen? Solving the problem and troubleshooting

Catalog sections

Special offer

Installation, repair of water heaters Termex, ETALON, GARANTERM, Edisson, REAL, ATT, ISEA, ARISTON, POLARIS, OKA, Atlantic, etc.

rub. at the price of rub.

Special offer

Special offer

Water heater Termex Blitz 10 O

7200 rub. 5600 rub.

Special offer

Water heater Termex IF 50 V

14620 rub. 12200 rub.

Special offer

Water heater Termex ID 80 V

19500 rub. 17000 rub.

Why is my kitchen faucet noisy? We solve the problem and troubleshoot!

Many will agree that when a faucet in the kitchen makes noise, this is an unpleasant phenomenon that not only distracts attention, but also significantly spoils the mood. However, few people know that you can fix the problem yourself.

The faucet in the kitchen is noisy - what is the reason and how to fix it

The cavitation process is the culprit for your kitchen faucet making noise. It doesn't just happen. In the mixer, its occurrence provokes the deterioration of parts of the mechanism that move (a pressure drop is formed).

Keep in mind that the longer the noise is, the more likely it is that the faucet mechanism will suffer from the effects of cavitation. Therefore, if your mixer began to make a sound and vibrate, do not put off solving the problem indefinitely.

https://youtube.com/watch?v=qJ6HHOqLzD4

The method of troubleshooting the mixer depends on its type:

Faucets with a valve mechanism - consist of an axle box and a gasket (rubber or ceramic). One variety is only suitable for a certain type of water (hot or cold). If you have a faucet with a rubber gasket, then replace it. She could wear out. If the mechanism has a ceramic gasket, then the problem probably lies in the wear of the silicone fixing lining that holds the bay. More often, low-quality budget faucets are subject to cavitation. So do not save on them and get reliable

For example, pay attention to Edelform mixers.

Faucets with a single-lever mechanism - a feature of this group of faucets is their reliability and durability. One such faucet can be used for both hot and cold water.

Unlike faucets with a valve, single-lever mixers cannot be a source of noise. Sounds and vibrations appear with increased fluid pressure in the water supply (more than 2.5 atmospheres). Those. pipes make noise. You can eliminate the cause. This is done using a special mechanism (reducer), which will reduce the water pressure between the pipe and the system.

The crane should not hum

It is difficult to find a person who would not have encountered a situation where the mixer starts to make strange sounds, roar and make noise during operation. This phenomenon is called cavitation and is a decrease in pressure after the water leaves the cartridge.

Types of mixers

Mixers are of the following types:

Valve. In them, the speed and temperature of the water are regulated by simple valves, under which crane boxes are installed.

In the event of extraneous noise and leaks, you should pay attention to this particular structural element.
Lever mixers. Everything in them is regulated by a lever that can move in two planes.

In cartridge faucets, if extraneous sounds appear, the only way to repair is to completely replace the ceramic cartridge that has worn out during operation.

How to eliminate extraneous noise?

The easiest way is to purchase high-quality, proven sanitary ware - for example, buy a Teka faucet - it will last a long time and fit perfectly into the bathroom interior. But in some cases, for example, with a limited budget, renovation becomes an actual option.

If the mixer, equipped with a crane box with a rubber gasket, began to make noise, then it is necessary:

• turn off the water, preventing it from flowing into the mixer;
• disassemble the product by removing the valves that perform a decorative function;
• unscrew the bolts that secure the valves;
• remove the crane box itself, fixed in the mixer, assessing the wear of the rubber gasket installed there;
• in most cases, it will have to be replaced with a new one;
• then the product is assembled in the reverse order.

In most cases, this will be enough to get rid of extraneous noise for a long time.

If a product equipped with a ceramic axle box starts to make noise, then it is necessary to look for a problem in a silicone washer that presses the ceramic rings. By combining them, you can adjust the intensity of the water supply. In most cases, repairs are made solely by replacing a worn ceramic bushing.

Lever mixers are usually devoid of such problems and do not make noise. But if extraneous sounds appear during its operation, then it is necessary to replace the cartridge and, if this does not help, normalize the pressure in the pipes. This is usually done with the help of gearboxes - special devices installed in front of the mixer. They lower the pressure to a level of 2.5 atmospheres, after which the noise disappears forever.

How mechanical cleaning is performed

This option is acceptable only if the blockage has appeared in certain sections of the pipes. To do this, the water must be turned off. This is the first condition that must be met before starting any repair work. The disconnected pipe is cleaned with a thick wire, and for the best effect, a ruff is attached to it. If it is not possible to clean the hole (deposits on the walls have petrified and become part of the system), then this section is cut out and replaced with a new one. And to eliminate further problems, it is necessary to tightly fasten all the elements using sealed rubber gaskets.

Please note that even when disassembling the structure, you need to remember the location of all elements

Ways to eliminate blockage

You are mistaken if you think that it is worth pouring some unique liquid like Mole into the system and the problem will be solved. You will have to work on your own. The blockage can be removed in three ways:

• Hydraulic flush.
• Pneumatic flush.
• Mechanical cleaning.

Let's look at flushing first. This is the flow of water. To do this, it’s not enough just to connect the hose, so they use electric, fairly powerful pumps. However, in this way, blockages can only be eliminated in pipes of small diameter. This method is not suitable for thick products. In this case, heavy particles will still have time to settle on the walls.

Ways to solve the problem

A guarantee of the good condition of the water supply system is a competent hydraulic calculation. Only on its basis it is possible to correctly determine the diameter and material of pipes for communications.

The most radical solution to the problem that makes the system buzz loudly is to replace all old pipes and devices, including faucets, with new ones in your apartment. But it is not a fact that it will bring results if the pipeline in the entrance or house is also faulty. It is necessary to determine exactly where the reason for which the pipes are buzzing is located. Often these are valves and mixers.

Do-it-yourself valve repair or replacement

The design features of the valve valve often become a source of problems. The use of ball valves instead of valve type valves eliminates the need for frequent maintenance and replacement of gaskets. In new buildings, ball valves are already installed immediately, and there it buzzes much less often.

They are simpler and more efficient, although if they fail, they are practically beyond repair. This is not significant, because the cost of ball valves for apartment water supply is small. But if, nevertheless, you have a valve valve at the water inlet to the system at home, then repairing it yourself is cheaper than changing it.

To do this, you need to block the access of water to the riser (if the house is an apartment building). Try to unscrew the crane box (sometimes called the box). If the thread is stuck, then it will not be easy to unscrew it.In this case, the valve body is heated with a gas burner, the axle box is unscrewed and repaired.

Inside the apartment, locking devices work on a similar principle, with only a slight difference. In the bathroom and in the kitchen there are faucets that we interact with every day. They fail more often than the locking devices on the external pipeline. By design, they come with a rubber or ceramic seal.

Crane box with rubber

To repair the mixer, you need to find out which part, when turned on, is the reason that the apartment buzzes loudly. There are two options - this part is either on a cold pipeline or on a hot one. Further:

1. Shut off the water supply to the mixer.
2. Unscrew the failed crane box.
3. Inspect the condition of the rubber and the seat in the mixer body.
4. Change gasket on valve.
5. Screw the faucet box back into the housing.
6. Check the tightness with a test water supply.

Some plumbers simply cut the bevel on the gasket at a 45° angle, about 1mm. Sometimes these simple actions are enough: the pipe no longer hums.

Crane box with ceramics

If the crane box If your faucet has a ceramic seal, then the noise may be caused by a sagging silicone washer, which compresses the ceramic structural elements together. In this case:

1. Shut off the water supply.
2. Unscrew the crane box.
3. Inspect the condition of the silicone seal.
4. If the washer sags, cover its plane with plastic.
5. Screw the faucet box into the body.
6. Check the tightness with a test run of water.

Repair of ceramic crane boxes is an ineffective measure. If the part is out of order, it is better to replace it immediately.

Main reasons

1. Too high pressure in the pipeline - the sound is heard not only in the apartment, but throughout the entrance. One of the options is a pipeline malfunction in a hard-to-reach place. As a result, expensive repairs can be expected for you and your neighbors.
2. Worn metal pipeline. If the hum is heard without the water turned on, the reason for this is the accumulation of lime and other deposits on the walls of the pipes, as well as rust.
3. Mistakes that were made during the installation of the pipeline are a popular cause of unwanted sounds. So to begin with, after the occurrence of sounds, check the connection of all piping systems - this problem is also very popular.
4. One of the most obvious problems is a defective gasket. Because of it, not only will there be sound, but also the faucet will start to flow. It can be either a defective gasket or its incorrect installation.

Repair of locking devices with rubber gasket

All work consists of several stages.
.

A humming or buzzing sound from a socket or switch usually means that the wire is dead. If so, the switch or outlet may feel warm to the touch, although not necessarily. Loose wire is a fire hazard, so call an electrician right away to check for a buzz or hum.

Buzzing or buzzing noises from light fixtures could also indicate a simple wire, but with lights there's a good chance something else is to blame. If the buzzing light is on the dimmer switch, replace the lamp with a different type of lamp or one made by another company. Some lamps indicate on their packaging that they are designed to work with dimmers. If that doesn't end the sound, replace the dimmer. If the fluorescent lamp is making noise, the fixture's "ballast" may need to be replaced.

1. Turn off the water supply to the apartment.
2. A crane box is unscrewed from the mixer.

For a complete repair, it is desirable to unscrew it completely.

Crane box device

To do this, the crane must be disassembled.

1. Remove the protective cap from the lamb.
2. Loosen the locking screw with a screwdriver.
3. Unscrew the crane box with adjustable wrenches.

Assess the condition of the gasket
.

Scratches or rips off from inside a wall or ceiling.You can probably guess what this means - a rodent got into your house. Get it out as soon as possible. Or buy and install traps - avoid poisons that can be consumed by your pets or cause pests to die and rot inside your walls.

Lever Faucet Troubleshooting Solutions

Don't just evict the pest, also look for and seal the hole it used to get into your home so other animals can't get in. Expanding aerosol sealants are an easy and effective way to fill small gaps. One place to check: If you have crawlspace under your home, look at tubs, and showerheads often fail to properly seal holes under drains.

If the rubber is still soft, then cut the edges at an angle of 45 ° along the contour with scissors. If the gasket is "hardened" change to a new one. It is also advisable to cut the edges of the new gasket at the same angle.

Reassembly is done in much the same way. A fum tape (or tow) is wound around the threaded connection of the tap and the part is twisted into place.

Capel. Water leakage inside the wall can destroy the wall panel and insulation and lead to mold or mildew problems. Fortunately, not every sound of water signals a problem—sometimes water is safe inside pipes. First, check the basement or crawl under the spot where you hear the sound of the water. If there is a water leak, that water is likely to find its way there. If you see water or water damage, call a plumber immediately. If you can't find water under the dripping sound, but the disturbing water sound persists, perform a water loss test.

The water supply is opened on the water pipes and the operation of the tap is checked. If the water flows normally and there is no more noise, then the work has been completed successfully.

Crane repair

The cause of the noise may be a malfunction of the plumbing systems. It is worth noting that the main reason for the occurrence of an unpleasant sound is based on improper installation or a defect in such an element as a crane box gasket. If the reason is precisely in this gasket, then in addition to the annoying sound, a tap leak may occur. Therefore, repairs should be carried out immediately.

It is quite possible to repair a buzzing faucet yourself if you follow the instructions.

If the problem is a faucet malfunction, you should determine which one. A malfunction can be in the faucet of both cold water and hot. To do this, it is necessary to alternately open and close cold and hot water, this will make it possible to determine in which particular tap the malfunction is. Before starting work in the apartment, the water supply is shut off, after which the crane box is turned on. It is on it that the gasket is located, which is the source of problems. A faucet box is the main device that regulates the flow of water. Such a device is most often located under the main valve that supplies water.

The probable reason why the faucet is noisy can be a ceramic faucet.
And this is despite the fact that many people think that it is thanks to the ceramic element that such unpleasant moments can be avoided. The buzzing of the crane in this case may not begin immediately, but after some time. This, in particular, is due to the wear of the element or its incorrect installation.

To clarify what material the gasket is installed from, there is no need to unscrew the crane box. This can be recognized by closing or opening the water flow. If for full opening it is necessary to make several turns of the valve, then a rubber gasket is installed. If the water flow is blocked by one turn, then ceramics are used as the material.

Almost every adult has encountered such a phenomenon as an inexplicable noise coming from the mixer.In general, there is an explanation for everything and the unpleasant noise from the mixer - including. This common phenomenon is called cavitation. Its essence is as follows: after the water leaves the mixer cartridge, there is a sharp drop in water pressure - hence the noise. However, understanding the essence of the problem does not calm the nerves and we are faced with the need to eliminate the problem of a noisy mixer. How to do it? Let's try to consider this issue in detail, as well as find an acceptable solution to the problem.

The first thing to do is to decide in what conditions an unpleasant noise occurs. It will be necessary to finally determine its source. In other words, when cold or hot water is turned on, does the mixer begin to buzz? If you do not have a definite answer to this question, you can find out only by turning the cold water supply valve and then the hot water supply valve.

Causes of the problem

The main reason why there is a hum in the faucet is directly dependent on the sound waves that are generated during vibration. Therefore, it is initially necessary to determine the primary source of crane vibration. The main reasons include:

1. Very high water pressure in the pipeline. Such a phenomenon can provoke not only sounds that will be heard in your room, but also in neighboring apartments. Too much pressure can easily damage pipes, especially if the damage occurs in a hard-to-reach place. In this case, it may be necessary to carry out repairs not only in your own, but also in neighboring apartments along the riser.
2. If the water supply is made of metal pipes that have not changed for a long time. In this case, it is likely that the vibration occurs due to the fact that there are large accumulations of lime and other deposits on the walls.
3. Unpleasant sounds can occur during the passage of water through metal pipes if the plumbing is not done correctly.
4. The most common reason a faucet hums is a leak in the faucet. It may be incorrectly installed or defective.

To avoid problems of various kinds, it is necessary to initially think over and design the pipeline. The entire system must withstand a certain pressure that will act in the pipe during operation.

Also, attention must be paid to the installation of the plumbing system. Particular attention should be paid to the faucet gaskets

Higher quality is the key to long-term use.

If we consider the first two cases, in order to radically solve the problem, it is necessary to completely replace the pipes and install new ones. It is recommended to install plastic instead of metal. But this may not give a 100% result, since in order to eliminate sound, the plumbing must be changed not only in your apartment, but also in the next one.

Cleaning pipes from accumulated contaminants on the walls can also help solve the problem. This method is quite laborious, but you must be prepared for the fact that pipe cleaning will not completely eliminate the problem and regular cleaning will be required.

Determine the pressure level

To understand the cause of the defect, since it could be high pressure, do a little test: turn on the tap and turn off the tap - that's all that needs to be done.

You may have heard a buzzing sound after closing a cold tap, which means that this is high pressure. What to do if the cold water tap is buzzing, you will learn below.

Solving the problem is not very difficult: you need to install a special air chamber on the pipe, in front of the tap. It will absorb sudden pressure surges in the pipe.

Chamber operation: the air inside the chamber is compressed and softens the blow during the closing of the faucet. There are two ways to install the camera:

• using a special additional pipe section;
• using a special muffler of a humming crane.

Expert answers

Julia:

Replacing the gasket will not always eliminate such noise and roar. Since this happens not only because of the worn gasket, but also because of the loosening of the very fastening of this gasket on the crane box screw. So it’s better to change the entire axle box at once - they are not so expensive

342:

change the gasket.

Victoria:

If your tap is CLOSED, and the sound is still heard, then it is not you who are buzzing, but the neighbors. And when you open it, the water pressure decreases, so it stops buzzing. So you need to beat the neighbors in the face / change their tap. I sympathize. My upper neighbor, a lonely teacher, was buzzing for almost half a year, until she bothered to turn to a plumber.

Evgeniy:

won't break. It usually buzzes if the gaskets are missing or the very fastening of this gasket is loose, close it tight and call the plumber tomorrow Victoria Ostafeychuk is probably right

ROSYURI:

Yes, what is the question? Replace it and all that business. The design, its hydrodynamics are poor, there are such. 5 minutes of work and the whole country already knows about it!

Grandfather Au:

The crane buzzes and thumps because of the gasket on the axle box, if it starts thumping strongly, this is already hydraulic shocks, it can tear off the decayed thread. Replace the axle box with a ceramic one and forget about it

Len.to4ka:

We were helped by changing the gasket.

dmitry gusev:

Ah, there you are. Finally you have been found. You haven't let me sleep for a whole week.

Aelita:

It's almost 2 am now and the same problem now I know what to do in the morning :)))

Argentina Christoforov:

I confirm the words of the topikstarter - I have the same story: Ango art shower faucet. FT 200-21 with quarter-turn ceramic disc cocks, intermittently hums in hot water when turned off. The effect began to be observed after the tap did not work for half a year, the water was turned off. Light pressure on the valve stem eliminates noise. Mixer Chinese economy segment, worked for several years. I suppose it buzzes during periods of increased water pressure, because at this time it also lets water through (leaks), although the day before I lubricated the discs with Electrolux special grease, I thought the grease might eliminate the buzz.

sergey sevastyanov:

if the kranbuksa ceramic is buzzing, it’s easier to replace it. but if there is no time, etc., immediately replace it, pull a piece of cellophane over the gasket in several layers and tighten it - the noise will stop

Konstantin S.:

I'm sure you have ceramic cranks. They have small holes for water to pass through. The smaller the holes, the more noise. open both faucets, the noise is 2 times stronger. In the bathroom. closet can be pressed, close the taps to reduce pressure. Less pressure means less noise. This solution is not clear

Andrey:

This is because the “skimmer” built into the mixer works especially well when mixing water of different temperatures. Turn off the "skimmer" from the network! :) It is so small in the form of a barb and you can't even get to it by disassembling the mixer. Remove the mixer and give it back to where you took it due to internal marriage

vano-nv:

If the mixer costs less than 3 thousand, it is simply obliged to make noise

Cornelius Schnapps:

If the mixer buzzes like a trombone, change the gaskets on the granboxes. If it's just making noise, change the faucet. Within 14 days I have to take it back and refund the money.

day Night:

put a reducer at the inlet of the system (reduces pressure)

AMIGO:

maybe because it's cheap?

Why is the faucet in the kitchen or bathroom noisy

The noise coming from different types of mixers has several causes. Most often, such noises are emitted by structures with a rubber gasket. But the same noise is possible in ceramic axle boxes - there is already a marriage made during production. Lever mixers make noise much less often.

If both faucet valves make noise at the same time, this may be due to high water pressure - this often happens in modern high-rise buildings. Inexpensive products cannot boast of a massive body, so cavitation and microscopic water hammer are possible.

Mixer noise is often referred to as tap noise.

Having opened the gasket, you need to pay attention to whether the pipes are securely fixed and whether all fasteners are available. This will eliminate strong vibration

A similar situation in the case of hard eyeliner is much less common.

Exceeding the upper limit of normal

Since it is not always easy to understand why the faucet is buzzing, it is best to seek help from professionals. For a normal job, he will quickly assess the situation and find the right solution. Sometimes he may be powerless and advise you to contact the water service provider. If water enters the system under high pressure, you can’t do anything on your own with a buzz.

Here the question would be logical: what is the normal water pressure in the system? Usually this figure is 2 atm. This indicator is optimal for the operation of a washing machine or dishwasher. However, the upper limit is 6 atm. In this case, you need to deal with the service provider until you find the best solution.